Pelco C3426M-D User Manual

INSTALLATIONC3426M-D (3/08)IS110 SeriesCamclosure®Integrated Camera System

10 C3426M-D (3/08)8. Reinstall the back box inside the cover. For vandal-resistant installations, rotate the back box to position the conduit plug op

C3426M-D (3/08) 116. Connect the power wires, refer to Table D.AC operation only: If you are wiring more than one Camclosure to the same transformer,

12 C3426M-D (3/08)404 PLASTER RING INSTALLATIONNOTE: You should install the camera module into the back box before installing the back box into the c

C3426M-D (3/08) 136. Reinstall the back box inside the cover. For vandal-resistant installations, rotate the back box to position the conduit plug op

14 C3426M-D (3/08)SIDE CONDUIT INSTALLATIONNOTE: You should install the camera module into the back box before installing the back box into the cover

C3426M-D (3/08) 158. Connect the video cable/wires:• BNC: Connect the BNC connector from the unit to a mating BNC connector.• UTP: Connect the blue w

16 C3426M-D (3/08)Camera ModuleThe IS110 Series Camclosure camera module includes the camera, camera bracket, and heater board. To perform most camer

C3426M-D (3/08) 172. Unplug the camera (10-pin), service (3-pin), and heater board (4-pin) connectors from the back box (refer to Figure 7).Figure 7.

18 C3426M-D (3/08)CAMERA ORIENTATIONAt the factory, the camera module is configured for ceiling mounting. For wall mounting, you must change the came

C3426M-D (3/08) 19Camera AdjustmentsTo perform the following camera adjustments, make sure to plug in the camera and service connectors. You may have

2 C3426M-D (3/08)

20 C3426M-D (3/08)DN/CH SERIES ADJUSTMENTSRefer to Figure 10 to adjust the IS110-DN or IS110-CH model.Figure 10. Adjusting the IS110-DN/CH Series Cam

C3426M-D (3/08) 21SW4-4: FlickerlessIn certain lighting conditions, a flicker in the light source may affect camera operation. Flickering can be caus

22 C3426M-D (3/08)VERTICAL PHASE ADJUSTMENTNOTE: Use this procedure for 24 VAC operation only.When using more than one camera power supply, a brief v

C3426M-D (3/08) 23DAY/NIGHT OPERATIONNOTE: This section only applies to DN model cameras.DN model cameras regularly check the brightness level of the

24 C3426M-D (3/08)DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTSRefer to Figure 12 to adjust the IS110-DW or IS110-CW model.Figure 12. Adjusting the I

C3426M-D (3/08) 25SW1-4: Auto White Balance/Manual White BalanceAuto white balance (AWB) is enabled by default (ON).To manually set and lock the whit

26 C3426M-D (3/08)SW1-8: Day/Night Operation (DW models only)NOTE: On CW models, SW1-8 is unused and does not affect camera operation.DW model camera

C3426M-D (3/08) 27AUTO IRIS LEVEL ADJUSTMENTThe electronics of the IS110-DW and IS110-CW Series Camclosures automatically adjust the camera to the au

28 C3426M-D (3/08)Camera PositioningRotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis ì in Figure 14).NOTE

C3426M-D (3/08) 29Install Liner and Trim Ring1. Adjust the liner (if installed), refer to Figure 15:a. Align the screw holes in the trim ring with th

C3426M-D (3/08) 3ContentsRegulatory Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 C3426M-D (3/08)Service ConnectorThe IS110 Series Camclosure integrated camera system includes a service connector that outputs camera video. Use i

C3426M-D (3/08) 31To assemble the cable:1. Attach the CPM 88 miniature coaxial connector to one end of the cable. Follow the directions supplied with

32 C3426M-D (3/08)SpecificationsGENERALPan/Tilt Adjustment ManualPan 360°Tilt 80° (20° to 100° range) Rotation 360°Construction Aluminum with steel c

C3426M-D (3/08) 331.797(4.56)3.593(9.13)Ø 0.343NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE IN INCHES.5.50(13.97)3.79(9.63)4.01(10.19)

34 C3426M-D (3/08)

PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTYPelco will repair or replace, without charge, any merchandise proved defective in material or workmansh

Worldwide Headquarters3500 Pelco WayClovis, California 93612 USAUSA & CanadaTel: 800/289-9100Fax: 800/289-9150InternationalTel: 1-559/292-1981Fax:

4 C3426M-D (3/08)List of Illustrations1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C3426M-D (3/08) 5Regulatory NoticesThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

6 C3426M-D (3/08)DescriptionThe IS110 Series Camclosure® integrated camera system combines an environmental cover, back box, camera, lens, and lower

C3426M-D (3/08) 7The IS111 models include the following specifications: Indoor/outdoor dome, vandal resistant, surface mount, clear bubble, liner, an

8 C3426M-D (3/08)Figure 1. Package ComponentsCOVER ANDBACK BOX 1 EA.CAMERA MODULE1 EA.TRIM RING, LINER,AND CLEAR BUBBLE1 EA.TRIM RING ANDSMOKED BUBBL

C3426M-D (3/08) 9Cover and Back Box InstallationThe IS110 Series Camclosure integrated camera system mounts only to a surface. It can be wired throug