Pelco TI2550 User Manual Page 1

INSTALLATION/OPERATIONC1309M-A (9/08)TI2535 and TI2550 ModelsTI2500 SeriesFixed-MountThermal Imager

10 C1309M-A (9/08)CONNECT WIRING1. Pull the shielded power cable through the gland on the left side of the enclosure’s back plate.NOTES:• To prevent

C1309M-A (9/08) 114. Connect the input power wiring for either 24 VDC or 24 VAC to the screw terminals for pins 6 and 7 on the detachable connector (

12 C1309M-A (9/08)INTERFACING WITH A PC1. Attach the end of the serial cable that is not connected to the camera’s detachable connector to your PC’s

C1309M-A (9/08) 13FIELD SETUPDISASSEMBLE THE ENCLOSURE1. Use the supplied 1/8-inch hex wrench to loosen the two captive hex screws on the enclosure’s

14 C1309M-A (9/08)REASSEMBLE THE ENCLOSURE1. Place the supplied desiccant bag at the back of the enclosure.2. Make sure that the lubricated O-rings o

C1309M-A (9/08) 15ConfigurationThe camera setup must be complete before the camera can be configured (refer to Setup on page 7).To open the TI25 GUI

16 C1309M-A (9/08)Perform Manual FFCOccasionally, image quality may degrade. When this happens, perform a manual FFC. After manually performing this

C1309M-A (9/08) 17VIDEO TABCHANGING THE IMAGE ORIENTATION MODEImage orientation allows you to correct the video in the event that the camera is mount

18 C1309M-A (9/08)CHANGING THE POLARITY/LUT SETTINGThe Polarity/LUT setting programs the specific palette of colors to represent the temperatures in

C1309M-A (9/08) 19PanWhen the “Zoom 2x” check box is selected, you can move the zoomed array region within the full-array area; this digitally simula

2 C1309M-A (9/08)ContentsImportant Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 C1309M-A (9/08)AGC TABThe default settings on the automatic gain control (AGC) tab offer the best image quality for most scenes. You can make AGC

C1309M-A (9/08) 21LINEAR PARAMETERSThe linear parameters are made available depending on the mode selected.The following settings are available for L

22 C1309M-A (9/08)ABOUT TABClick the About tab (refer to Figure 9) to access basic camera information. If the camera is connected to the PC correctly

C1309M-A (9/08) 23InstallationThe TI2500 Series fixed-mount thermal imager can be mounted using an appropriate wall, ceiling, or pedestal mount (refe

24 C1309M-A (9/08)TroubleshootingNOTE: The system contains no user-serviceable parts. If there is a problem with your system, it must be returned to

C1309M-A (9/08) 25MaintenanceCLEANING THE LENS1. Saturate a piece of optical-grade tissue with deionized water and drape it over the lens.2. Let the

26 C1309M-A (9/08)SpecificationsElectricalInput Power 4 W, 6.2 VA nominalInput Voltage 18–27 VAC; 14–32 VDCPower Requirements 4 WHeater 24 VAC, dual

PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTYPelco will repair or replace, without charge, any merchandise proved defective inmaterial or workmanshi

Australia|Finland|France|Germany|Italy|Macau|The Netherlands|Russia|SingaporeSouth Africa|Spain|Sweden|United Arab Emirates|United Kingdom|United Stat

C1309M-A (9/08) 3List of Illustrations1 Exploded View of TI2500 Series Thermal Imager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 C1309M-A (9/08)Important Safety Instructions1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5

C1309M-A (9/08) 5Regulatory NoticesThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

6 C1309M-A (9/08)DescriptionThe TI2500 Series combines a powerful advanced thermal imaging device in a compact fixed-mount environmental enclosure.Th

C1309M-A (9/08) 7SetupBefore configuring the camera settings or installing the unit, you must remove the camera assembly from the enclosure to set up

8 C1309M-A (9/08)INSTALLING SOFTWAREMINIMUM SYSTEM REQUIREMENTS• PC (Pentium® Pro processor, 166 MHz) with Windows® NT 4 (or later, not including Win

C1309M-A (9/08) 9BENCH SETUPDISASSEMBLE THE ENCLOSURE1. Use the supplied 1/8-inch hex wrench to loosen the two captive hex screws on the enclosure’s