Pelco C1302M-F User Manual

INSTALLATIONC1302M-F (11/08)ExSite® SeriesExplosionproofPan and Tilt System

10 C1302M-F (11/08)ADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-849 ON OFF OFF OFF ON ON OFF OFF50 OFF ON OFF OFF ON ON OFF OFF5

C1302M-F (11/08) 11Table B. D Protocol Receiver Address (Continued)ADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8143 ON ON ON O

12 C1302M-F (11/08)ADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8239 ONONONONOFFONONON240 OFF OFF OFF OFF ON ON ON ON241 ON OFF

C1302M-F (11/08) 13Install the Camera ModuleTo install the camera module do the following:1. Refer to Figure 4. Loosen the set screw at the back of th

14 C1302M-F (11/08)3. Slide the camera module into the enclosure. Refer to Figure 6 to position the camera module properly in the enclosure. Carefully

C1302M-F (11/08) 154. Refer to Figure 8 and do the following to install the arm of the wiper:a. Place the supplied green bushing on the stud located b

16 C1302M-F (11/08)Install the Pan and Tilt Unit1. Check for proper seating of the power module seal. Make sure the seal is fully seated in the groove

C1302M-F (11/08) 17Install the Sun Shroud1. Place the supplied nylon washers on the 6-32 Phillips pan head screws. Refer to Figure 11.2. Align the mou

18 C1302M-F (11/08)MaintenanceCAMERA MODULE REPLACEMENTTo replace the camera module do the following:1. Remove the back cap of the camera enclosure. R

C1302M-F (11/08) 193. For models with wipers, also remove the wiper arm and the green bushing from the unit (see Figure 13). 4. Slide the camera modul

2 C1302M-F (11/08)

20 C1302M-F (11/08)6. Refer to Figure 13 and do the following to reinstall the arm of the wiper:a. Reinstall the green bushing on the stud located beh

C1302M-F (11/08) 21SpecificationsELECTRICALInput Voltage 24 VAC or 100-240 VACInput Voltage Range ±10%Power Consumption Maximum 60 W (120 VA) per sy

22 C1302M-F (11/08)*Manual control of camera setup functions can be done with CM6700, CM6800, CM8500, CM9500, CM9740, CM9760, CM9770, CM9780, KBD200

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.This equipment con

Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USAUSA & Canada Tel (800) 289-9100 Fax (800) 289-9150Internatio

C1302M-F (11/08) 3ContentsImportant Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 C1302M-F (11/08)Important Safety Instructions1. Read these instructions. 2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.

C1302M-F (11/08) 5Getting StartedThank you for purchasing Pelco’s ExSite® Series explosionproof integrated positioning system. This manual includes in

6 C1302M-F (11/08)Install the Power ModuleAttach the power module to the mounting surface. Use only installation methods and materials capable of supp

C1302M-F (11/08) 7CONNECT WIRINGRefer to the following information to connect the wires and cables as required.NOTES: • Relay 3 is allocated specific

8 C1302M-F (11/08)DIP SWITCH SETTINGSConfigure the receiver address, termination, and baud setting for the system. The DIP switches to configure these

C1302M-F (11/08) 9ADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-81 OFF OFF OFF OFF OFF OFF OFF OFF2 ON OFF OFF OFF OFF OFF OFF OF