Pelco EH3512 User Manual

®INSTALLATIONEH3508/EH3512/EH3515 Series Environmental EnclosureC478M-M (1/06)

10 C478M-M (1/06) Figure 5. EH3512 Series Wiring Diagram NOTE: Blower applies to -1/-2/-3 models only.12345678910HEATERDIODEBRIDGEINPUT, AC HIGH

C478M-M (1/06) 11 Figure 6. EH3515 Series Wiring Diagram NOTE: Blower applies to -1/-2/-3 models only.12345678910INPUT, AC HIGHINPUT, AC LOW (NE

12 C478M-M (1/06) Table A. Enclosure Accessory Wiring Distances The following cable sizs are the minimum recommended for sue with the heater and d

C478M-M (1/06) 13 Table A. Enclosure Accessory Wiring Distances (Continued) Model NumberInput VoltageAccessoriesMax. Power ConsumptionCable Size

14 C478M-M (1/06) Example: An enclosure that requires 30 VA and is installed 94 feet (28 m) from the transformer would require a minimum wire gauge

C478M-M (1/06) 15 Operation If your enclosure has a thermostatically controlled heater, the thermostat is set to turn on at 50°F (10°C) and to turn

16 C478M-M (1/06) Specifications Camera Mounting Multiple holes on adjustable camera sled; camera sled mounts in threaded strip for easier removal an

C478M-M (1/06) 17 Figure 7. EH3508, EH3512, EH3515 Dimension Drawing5.14(13.05)3.88(9.86)2.00(5.08)ABCEH3512 EH3515A 14.75 (37.47) 17.75 (45.09)B

18 C478M-M (1/06)REVISION HISTORYManual # Date CommentsC478M-J 6/99 Moved the EH3508 Series enclosures from manual C1435M-A. Updated the descripti

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workma

®Worldwide Headquarters3500 Pelco WayClovis, California 93612 USAUSA & CanadaTel: 800/289-9100Fax: 800/289-9150InternationalTel: 1-559/292-1981Fax

C478M-M (1/06) 3 Important Safety Instructions Prior to installation and use of this product, the following WARNINGS should be observed.1. Read thes

4 C478M-M (1/06) Description The EH3508/EH3512/EH3515 Series are indoor/outdoor light-duty camera enclosures designed for use with various cameras o

C478M-M (1/06) 5 Installation The following items are supplied to mount the enclosure:2 1/4-20 x 0.500-inch hex head screws2 Flat washers2 Split was

6 C478M-M (1/06) Figure 2. Exploded View of EH3500 Series AssemblyFLAT WASHERSPLIT WASHERHEX HEAD SCREWEM1450 WALL MOUNT (NOT SUPPLIED)GLANDSPHILL

C478M-M (1/06) 7 Perform the following steps to install the enclosure, camera, and lens:1. Unlatch and open the lid.2. Remove the camera sled from t

8 C478M-M (1/06) 9. If the enclosure has accessories that require power, you will need to access the PC board. To remove the cover, insert a screwdr

C478M-M (1/06) 9 Figure 4. EH3508-1/-2/-3 Wiring Diagram12345678910HEATERDEFROSTERINPUT, AC HIGHINPUT, AC LOW (NEUTRAL)24/120/230 VACMODELS