Pelco C1306M User Manual

ExSite ™ EHXM SeriesExplosionproofFixed System INSTALLATION C1306M (8/05)

10 C1306M (8/05)Table B. D Protocol Receiver Address (Continued)ADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8143 ON ON ON ON

C1306M (8/05) 11ADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8239 ON ON ON ON OFF ON ON ON240 OFF OFF OFF OFF ON ON ON ON241 ON

12 C1306M (8/05) Install the Camera Module To install the camera module, do the following:1. Refer to Figure 4. Loosen the set screw at the back of t

C1306M (8/05) 13 3. Slide the camera module into the camera enclosure. Refer to Figure 6 to position the camera module properly in the camera enclosu

14 C1306M (8/05) 4. Models with a wiper: Refer to Figure 8 and do the following to install the arm of the wiper:a. Place the supplied green bushing

C1306M (8/05) 15 Install the Enclosure and Set Pan Position 1. Lightly apply O-ring lubricant (supplied) to the O-ring, and then install the O-ring o

16 C1306M (8/05) Set the Tilt Angle of the Camera Module 1. Place a 41 mm open end or crescent wrench on the tilt locking nut and a 21 mm open end wr

C1306M (8/05) 17 Install the Sun Shroud 1. Place the supplied nylon washers on the 6-32 Phillips pan head screws. Refer to Figure 12.2. Align the mou

18 C1306M (8/05) Maintenance CAMERA MODULE REPLACEMENT To replace the camera module, do the following:1. Remove the back cap of the camera enclosure.

C1306M (8/05) 19 3. Models with a wiper: Remove the wiper arm and the green bushing from the unit (refer to Figure 14). 4. Slide the camera module o

2 C1306M (8/05) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 C1306M (8/05) 6. Models with a wiper: Refer to Figure 14 and do the following to reinstall the arm of the wiper:a. Reinstall the green bushing on

C1306M (8/05) 21 Specifications ELECTRICAL Input Voltage 24 VAC or 100-240 VACInput Voltage Range ±10%Power Consumption Maximum 60 watts (120 VA) pe

22 C1306M (8/05) *Manual control of camera setup functions can be done with CM6700, CM6800, CM8500, CM9500, CM9740, CM9760, CM9770, CM9780, KBD200A

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material orworkman

Worldwide Headquarters3500 Pelco WayClovis, California 93612 USAUSA & CanadaTel: 800/289-9100Fax: 800/289-9150InternationalTel: 1-559/292-1981Fax:

C1306M (8/05) 3 Important Safety Instructions 1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5

4 C1306M (8/05) Getting Started Thank you for purchasing Pelco’s ExSite ™ EHXM Series explosionproof system. This manual includes instructions for i

C1306M (8/05) 5 Install the Power Module Attach the power module to the mounting surface. Use only installation methods and materials capable of supp

6 C1306M (8/05) CONNECT WIRING Refer to the following information to connect the wires and cables as required. NOTES: • Relay 3 is allocated specifi

C1306M (8/05) 7 DIP SWITCH SETTINGS Configure the receiver address, termination, and baud setting for the system. The DIP switches to configure these s

8 C1306M (8/05)ADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-81 OFF OFF OFF OFF OFF OFF OFF OFF2 ON OFF OFF OFF OFF OFF OFF OFF3

C1306M (8/05) 9ADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-849 ON OFF OFF OFF ON ON OFF OFF50 OFF ON OFF OFF ON ON OFF OFF51 O