Pelco ES31C User Manual download pdf (Page 15)

C307M-I (11/05) 15

PATTERNS

The Esprit system can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This pattern can

consist of any standard pan and tilt or lens command. Presets, ﬂip, digital zoom, proportional pan, and turbo are not allowed in a pattern.

Zones can be enabled while running a pattern. Refer to the documentation for your control system to program and run patterns.

PARK

If the system does not receive any commands for a speciﬁed period of time (refer to the

Park Time Minutes

section), the system goes to preset 1

and parks. If the time speciﬁed is zero, or if preset 1 has not been programmed, the pan and tilt will not park.

IR FILTER (MODELS ES30CBW18, ES31CBW18, ES30CBW24, AND ES31CBW24)

The ES30CBW18, ES31CBW18, ES30CBW24, and ES31CBW24 models have an IR (infrared) lens ﬁlter that can switch in and out, automatically

or manually, depending on how the system is programmed. When the ﬁlter is IN, the camera produces a color picture. When the IR ﬁlter switches

OUT, the picture changes to black and white, increasing visibility in low light conditions.

The Auto IR Level setting controls automatic operation of the ﬁlter. To manually override automatic operation, use presets 88 (ﬁlter IN) and 89

(ﬁlter OUT). The unit will remain in manual control until it is panned or tilted more than 15 degrees.

NOTE:

LOW LIGHT does not mean NO LIGHT. Some type of illumination is required (street light, IR light, etc.).

AUTO IRIS

If auto iris is in the auto mode, it remains that way until you manually open or close the iris. The system will return to auto iris when it is panned

or tilted more than 15 degrees.

WIPER

The ES31C Series features a window wiper to clear moisture from the enclosure glass. There are two modes of operation for the wiper,

momentary and continuous. The wiper mode is easily set up through on-screen programming (refer to the

Wiper Mode

section).

To operate the wiper do the following:

Momentary Mode:

To operate the wiper one full cycle, press the AUX 1 button on your controller. Each press of the button operates the wiper

one full cycle, even if the AUX 1 button is latching. If AUX 1 is latching, the ﬁrst press will activate the wiper (open the latch). Pressing AUX 1 a

second time closes the latch, but will not cycle the wiper. Press the AUX 1 key again to cycle the wiper.

Continuous Mode:

To operate the wiper press the AUX 1 button on your controller. The wiper will continue to operate until the AUX 1 button is

pressed again or until the programmed cycle is completed.

NOTE –

CM9740 and CM9760 matrix systems only:

For the wiper to operate in continuous mode, the AUX 1 function in the camera ﬁle must

be set to latching. If the AUX 1 camera ﬁle is not latching, the wiper will only operate in momentary mode, even if the Esprit wiper is

programmed for continuous operation. Refer to the operation manual supplied with the CM9740 or CM9760 matrix system for instructions.

OPEN COLLECTOR AUXILIARY OUTPUT

An AUX 2 command from the controller will activate a device, such as a relay. The output will remain active for two seconds and then deactivate,

even if the controller is set to latching mode.

Examples of devices that can be used with AUX 2 are a washer assembly (not supplied by Pelco) or a latching relay (not supplied by Pelco)

attached to control a gate, lights, etc.

If a relay is used it must require less than 32 VDC and 40 mA to trigger the relay coil. The relay must be placed within 100 feet (30 m) of the Esprit

unit.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 67 68

Comments to this Manuals

No comments

Pelco ES31C User Manual Page 15

Comments to this Manuals

Related products and manuals for Security cameras Pelco ES31C