Pelco IS150 User Manual Page 1

INSTALLATIONC3427M-D (2/09)IS150 SeriesCamclosure®Integrated Camera System

10 C3427M-D (2/09)SUSPENDED CEILINGNOTE: You should install the camera module into the back box before installing the back box into the surface. When

C3427M-D (2/09) 114S DEEP ELECTRICAL BOXNOTE: You should install the camera module into the back box before installing the back box into the surface.

12 C3427M-D (2/09)Camera ModuleThe IS150 Series Camclosure camera module includes the camera, camera bracket, and heater board. To perform most camera

C3427M-D (2/09) 132. Unplug the camera (10-pin), service (3-pin), and heater board (4-pin) connectors from the back box (refer to Figure 6).Figure 6.

14 C3427M-D (2/09)CAMERA ORIENTATIONAt the factory, the camera module is configured for ceiling mounting. For wall mounting, you must change the camer

C3427M-D (2/09) 15Camera AdjustmentsTo perform the following camera adjustments, make sure to connect the camera and service connectors. You may have

16 C3427M-D (2/09)To adjust the focus:1. Loosen the focus locking screw.2. Position the inverted dome approximately 0.125 inch (3.175 mm) from the fro

C3427M-D (2/09) 17DN/CH SERIES ADJUSTMENTSRefer to Figure 10 to adjust the IS150-DN or IS150-CH model.Figure 10. Adjusting the IS150-DN/CH Series Camc

18 C3427M-D (2/09)SW4-4: FlickerlessIn certain lighting conditions, a flicker in the light source may affect camera operation. Flickering can be cause

C3427M-D (2/09) 19VERTICAL PHASE ADJUSTMENTUse this procedure for 24 VAC operation only.When using more than one camera power supply, a brief vertical

20 C3427M-D (2/09)DAY/NIGHT OPERATIONNOTE: This section only applies to DN model cameras.DN model cameras regularly check the brightness level of the

C3427M-D (2/09) 21DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTSRefer to Figure 12 to adjust the IS150-DW or IS150-CW model.Figure 12. Adjusting the IS

22 C3427M-D (2/09)SW1-4: Auto White Balance/Manual White BalanceAuto white balance (AWB) is enabled by default (ON).To manually set and lock the white

C3427M-D (2/09) 23SW1-8: Day/Night Operation (DW models only)NOTE: On CW models, SW1-8 is unused and does not affect camera operation.DW model cameras

24 C3427M-D (2/09)AUTO IRIS LEVEL ADJUSTMENTThe electronics of the IS150-DW and IS150-CW Series Camclosures automatically adjust the camera to the aut

C3427M-D (2/09) 25Camera PositioningRotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis ì in Figure 14).NOTE:

26 C3427M-D (2/09)Install Liner and Trim Ring1. Adjust the liner (if installed), refer to Figure 15:a. Align the screw holes in the trim ring with tho

C3427M-D (2/09) 27Service ConnectorThe IS150 Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it

28 C3427M-D (2/09)To assemble the cable:1. Attach the CPM 88 miniature coaxial connector to one end of the cable. Follow the directions supplied with

C3427M-D (2/09) 29SpecificationsGENERALPan/Tilt Adjustment ManualPan 360°Tilt 80° (20° to 100° range) Rotation 360°Construction Aluminum with steel ca

C3427M-D (2/09) 3ContentsRegulatory Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 C3427M-D (2/09)CAMERA/LENSIf you need technical specifications for the camera itself, refer to the IS150 specification online at www.pelco.com.(Des

PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTYPelco will repair or replace, without charge, any merchandise proved defective in material or workmansh

Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USAUSA & Canada Tel (800) 289-9100 Fax (800) 289-9150Internatio

4 C3427M-D (2/09)List of Illustrations1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C3427M-D (2/09) 5Regulatory NoticesThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

6 C3427M-D (2/09)DescriptionThe IS150 Series Camclosure® integrated camera system combines an environmental cover, back box, camera, lens, and lower d

C3427M-D (2/09) 7Indoor/outdoor dome, vandal resistant, in-ceiling mount, clear bubble, liner, gray finishPARTS LISTTable B. IS151, Clear Bubble with

8 C3427M-D (2/09)Figure 1. Package ComponentsBACK BOX1 EA.< OR >1/8-INCH HOLLOW SCREWDRIVER BIT1 EA.ADAPTER PLATE1 EA.SHOWN ACTUAL SIZESHIPPING

C3427M-D (2/09) 9Cover and Back Box InstallationThe IS150 Series Camclosure integrated camera system mounts only into a wall or ceiling.UNSHIELDED TWI